Influence of Al3+ doping for V5+ on the structural,optical, thermal and electrical properties of V2-xAlxO5-δ (x=0–0.20) ceramics

This paper reports an investigation on the structure-properties correlation of trivalent metal oxide (Al₂O₃)-doped V₂O₅ ceramics synthesized by the melt-quench technique. XRD patterns confirmed a single orthorhombic V₂O₅ phase formation with increasing strain on the doping of Al₂O₃ in place of V₂O₅ in the samples estimated by Williamson-Hall analysis. FTIR and Raman investigations revealed a structural change as [VO₅] polyhedra converts into [VO₄] polyhedra on the doping of Al₂O₃ into V₂O₅. The optical band gap was found in a wide semiconductor range as confirmed by UV–visible spectroscopy analysis. The thermal and conductivity behavior of the prepared samples were studied using thermal gravimetric analysis (TGA) and impedance analyzer, respectively. All the prepared ceramics exhibit good DC conductivity (0.22–0.36 Sm^-1) at 400 ?C. These materials can be considered for intermediate temperature solid oxide fuel cell (IT-SOFC)/battery applications due to their good conductivity and good thermal stability.     

The influence of processing methods on the dielectric properties of BaTi1-xGdxO3-x/2 - Based materials

In this study, the intermediate rare-earth oxide Gd₂O₃ (Gd) was substituted in different amounts (x = 0.2–2 mol%) for the formulation of BaTi_1-xGd_xO_3-x/2 (BTG_x) dielectric materials. The effect of B-site substitution was confirmed by the additional Raman active A_1g octahedral peak at ~835cm^-1 strengthened at x ≥ 0.4 mol%. Additionally, properties of 0.9BTG_0.007-0.1BA dielectric ceramics were analysed based on the influence of various processing methods as a function of sintering temperature. The focal samples were labelled Method-A (direct-mix) and Method-B (indirect-mix). As the sintering temperature (1075–1200 °C) increased, the 1 kHz response of the ε–T curves of Method-A samples transformed from a single peak to broad-narrow double peaks of high dielectric loss tangent (tan δ). Nonetheless, samples of Method-B possessed a clearly defined transmission electron microscopy (TEM) core-shell structure, flattened double-peak ε-T curves, optimised dielectric properties (ε = ~1563–1851 and tan δ < 1.5% at room temperature), and a wide-ranging temperature behaviour that meets the X8R dielectric standards (ΔC/C_25°C < ±15%). The maximum dielectric breakdown strength of Method-B samples reached ~131 kVcm, while the energy storage density was ~0.726 J/cm³ at a maximum efficiency of ~80% at 1100 °C. Thus, exhibiting good potentials for balancing temperature stability with energy storage applications.     

Predetermination of potential plastic hinges on reinforced concrete frames using GFRP reinforcement

In the past, glass fiber-reinforced polymer (GFRP)-reinforcement has been successfully applied in reinforced concrete (RC) structures where corrosion resistance, electromagnetic neutrality, or cuttability were required. Previous investigations suggest that the application of GFRP in RC structures could be advantageous in areas with seismic activity due to their high deformability and strength. However, especially the low modulus of elasticity of GFRP limited its wide application as GFRP-reinforced members usually exhibit considerably larger deformations under service loads than comparable steel-reinforced elements. To overcome the aforementioned issues, the combination of steel and GFRP reinforcement in hybrid RC sections has been investigated in the past. Based on this idea, this paper presents a novel concept for the predetermination of potential plastic hinges in RC frames using GFRP reinforcement. To analyze the efficiency of the concept, nonlinear finite element simulations were performed. The results underscore the high efficiency of hybrid steel-GFRP RC sections for predetermining potential plastic hinges on RC frames. The results also indicate that the overall seismic behavior of RC structures could be improved by means of GFRP as both the column base shear force during the seismic activity as well as the plastic deformations after the earthquake were considerably less pronounced than in the steel-reinforced reference structure.     

Subdivision based isogeometric analysis for geometric flows

We present a new isogeometric analysis (IGA) approach based on extended Loop subdivision scheme for solving various geometric flows defined on subdivision surfaces. The studied flows include the second-order, fourth-order, and sixth-order geometric flows, such as averaged mean curvature flow, constant mean curvature flow, and minimal mean-curvature-variation flow, which are generally derived by minimizing the associate energy functionals with $L^2$-gradient flow respectively. The geometric flows are discretized by means of subdivision based IGA, where the finite element space is formulated by the limit form of the extended Loop subdivision for different initial control meshes. The basis functions, consisting of quartic box-splines corresponding to each subdivided control mesh, are utilized to represent the geometry exactly. For the cases of the evolution of open surfaces with any shape boundary, high-order continuous boundary conditions derived from the mixed variational forms of the geometric flows should be implemented to be consistent with the isogeometric concept. For time discretization, we adopt an adaptive semi-implicit Euler scheme. By several numerical experiments, we study the convergence behaviors of the proposed approach for solving the geometric flows with high-order boundary conditions. Moreover, the numerical results also show the accuracy and efficiency of the proposed method.     

Hybrid hydrate processes for CO2/H2 mixture purification: A techno-economic analysis

In this work, hydrate based separation technique was combined with membrane separation and amine-absorption separation technologies to design hybrid processes for separation of CO₂/H₂ mixture. Hybrid processes are designed in the presence of different types of hydrate promoters. The conceptual processes have been developed using Aspen HYSYS. Proposed processes were simulated at different flow rates for the feed stream. A comprehensive cost model was developed for economic analysis of novel processes proposed in this study. Based on the results from process simulation and equipment sizing, the amount of total energy consumption, fixed cost, variable cost, and total cost were calculated per unit weight of captured CO₂ for various flow rates of feed stream and in the presence of different hydrate promoters. Results showed that combination of hydrate formation separation technique with membrane separation technology results in a CO₂ capture process with lowest energy consumption and total cost per unit weight of captured CO₂. As split fraction and heat of hydrate formation increases, the share of hydrate formation section in total energy consumption increases. When TBAB is applied as hydrate promoter, due to its higher hydrate separation efficiency, more amount of CO₂ is captured in hydrate formation section and consequently the total cost for process decreases considerably. Hybrid hydrate-membrane process in the presence of TBAB as hydrate promoter with 29.47 US$/ton CO₂ total cost is the best scheme for hybrid hydrate CO₂ capture process. Total cost for this process is lower than total cost for single MDEA-based absorption process as the mature technology for CO₂ capture.     

Systematic Review: Adipose-Derived Mesenchymal Stem Cells,Platelet-Rich Plasma and Biomaterials as New Regenerative Strategies in Chronic Skin Wounds and Soft Tissue Defects

The number of clinical trials evaluating adipose-derived mesenchymal stem cells (AD-MSCs), platelet-rich plasma (PRP), and biomaterials efficacy in regenerative plastic surgery has exponentially increased during the last ten years. AD-MSCs are easily accessible from various fat depots and show intrinsic plasticity in giving rise to cell types involved in wound healing and angiogenesis. AD-MSCs have been used in the treatment of soft tissue defects and chronic wounds, employed in conjunction with a fat grafting technique or with dermal substitute scaffolds and platelet-rich plasma. In this systematic review, an overview of the current knowledge on this topic has been provided, based on existing studies and the authors’ experience. A multistep search of the PubMed, MEDLINE, Embase, PreMEDLINE, Ebase, CINAHL, PsycINFO, Clinicaltrials.gov, Scopus database, and Cochrane databases has been performed to identify papers on AD-MSCs, PRP, and biomaterials used in soft tissue defects and chronic wounds. Of the 2136 articles initially identified, 422 articles focusing on regenerative strategies in wound healing were selected and, consequently, only 278 articles apparently related to AD-MSC, PRP, and biomaterials were initially assessed for eligibility. Of these, 85 articles were excluded as pre-clinical, experimental, and in vitro studies. For the above-mentioned reasons, 193 articles were selected; of this amount, 121 letters, expert opinions, commentary, and editorials were removed. The remaining 72 articles, strictly regarding the use of AD-MSCs, PRP, and biomaterials in chronic skin wounds and soft tissue defects, were analyzed. The studies included had to match predetermined criteria according to the patients, intervention, comparator, outcomes, and study design (PICOS) approach. The information analyzed highlights the safety and efficacy of AD-MSCs, PRP, and biomaterials on soft tissue defects and chronic wounds, without major side effects.     

Use of Fourier-Transform Infrared Spectroscopy (FT-IR) for Monitoring Experimental Helicobacter pylori Infection and Related Inflammatory Response in Guinea Pig Model

Infections due to Gram-negative bacteria Helicobacter pylori may result in humans having gastritis, gastric or duodenal ulcer, and even gastric cancer. Investigation of quantitative changes of soluble biomarkers, correlating with H. pylori infection, is a promising tool for monitoring the course of infection and inflammatory response. The aim of this study was to determine, using an experimental model of H. pylori infection in guinea pigs, the specific characteristics of infrared spectra (IR) of sera from H. pylori infected (40) vs. uninfected (20) guinea pigs. The H. pylori status was confirmed by histological, molecular, and serological examination. The IR spectra were measured using a Fourier-transform (FT)-IR spectrometer Spectrum 400 (PerkinElmer) within the range of wavenumbers 3000–750 cm⁻¹ and converted to first derivative spectra. Ten wavenumbers correlated with H. pylori infection, based on the chi-square test, were selected for a K-nearest neighbors (k-NN) algorithm. The wavenumbers correlating with infection were identified in the W2 and W3 windows associated mainly with proteins and in the W4 window related to nucleic acids and hydrocarbons. The k-NN for detection of H. pylori infection has been developed based on chemometric data. Using this model, animals were classified as infected with H. pylori with 100% specificity and 97% sensitivity. To summarize, the IR spectroscopy and k-NN algorithm are useful for monitoring experimental H. pylori infection and related inflammatory response in guinea pig model and may be considered for application in humans.     

Evaluation of the localized corrosion on Mg electrode surface by electrochemical noise technique

The symmetrical and asymmetrical electrodes made of Mg were studied in 0.1-M NaCl electrolyte adjusted at pH 12. The statistical and wavelet methods were employed for analyzing the electrochemical current noise (ECN) signals. The asymmetric configuration was used for electrochemical detection of filiform corrosion on Mg electrode. The real time scale of the dominant transients of the asymmetric electrodes was detected on the basis of the maximum peak in the SDPS plots. The SDPS values of the real time scale crystals of the ECN signals resulting from asymmetrical electrodes increased with the increase in immersion time due to the onset of filiform corrosion.     

A novel adaptive sampling based methodology for feasible region identification of compute intensive models using artificial neural network

Identification of feasible region of operations in multivariate processes is a problem of interest in several fields. This is particularly challenging when the process model is black-box in nature and/or is computationally expensive, as analytical solutions are not available and the number of possible model evaluations is limited. An efficient methodology is required to identify samples where the model is evaluated for developing a computationally efficient surrogate model. In this work, an artificial neural network based surrogate model is proposed which is integrated with a statistical-based approach (Jack-knifing) to estimate the variance of the surrogate model prediction. This allows implementation of an adaptive sampling approach where new samples are identified close to the feasible region boundary or in regions of high prediction uncertainty. The proposed approach performs better than a previously published kriging based method for different dimensionality case studies.